Carbide Tip

Carbide Tip

Tips and Tricks for Precision Drilling

Drilling a hole generally seems like quite a straightforward job. However getting a professional clean precise hole every time can be quite a task. Here are a few quick tips on how to make sure that you get the best results every time you are drilling a hole.

* Make sure that the work is fastened in the vice or clamps tightly. If possible make sure there is plenty of room for you to work in.

* Measure it out precisely, for most things you will probably only get one go at it, so get it right the first time.

* Make sure that you have quality drill bits that are sharp. This one tip here is probably the most important to getting the precision and clean finish you want. Obviously make sure it is the right drill bit for the job (metal, or masonry etc), and it is the right size for the hole you want.

* Let the bit drill bit do the work, don't push on it too hard. If you have to force it you probably need to sharpen the drill bit.

* When drilling into metal put a centre punch dent in.

* When drilling into hardwood or using large drill bits, make a pilot hole first.

* When drilling into plaster or ceramics put some masking tape over the area first to prevent cracking.

* If you are able to use a drill press. This will help with precision and drilling to uniform depths and angles.

* When drilling masonry, always use a masonry bit which has a special tungsten carbide tip welded into the twist part of the drill body which helps to cut into the masonry. When drilling into masonry always withdraw the tip every few seconds to remove debris and keep the tip cool. The job will be a lot easier if you get a drill with a hammer action.

* If you are drilling into plastics, you will want to go slowly, with slow rpm on the drill because you don't want to melt or split the plastic, or clog the drill bit.

* Use the different attachments available to make other jobs easier e.g. a disc sander, a buffer pad, a hole saw etc

* If you are using the drill for screwing you might want to invest in magnetic tips to hold the screw, it will be money well spent.

* Always do the job safely, use your protective equipment, especially eye protection. Disconnect the power and battery every time you change the drill bit and make sure the chuck is tight. Also make sure that there are no other hazards around before you start the job. One key point here is that when you are drilling into wall, make sure that there is no live wires you are drilling into.

So by following a few of these extra tips you will get a clean precise hole every time you use your drill and you will get the finish of a master craftsman. For more expert advice and a full range of drills, drill bits, drill accessories please visit our website at www.toolmart.com.au or come into one of our ten stores in Perth and Bunbury, we’ll be glad to help.
About the Author

For further information on hand tools, air tools and


href='<a href="http://toolmart.com.au">http://toolmart.com.au</a>'>power tools
and a full look at our

catalogue please visit our website at
http://www.toolmart.com.au
or go to

one of our 10 convenient locations throughout Perth and Bunbury.

Festool 491085 53.7mm Rebating Cutter Bit With Reversible Carbide Tip $122 53.7mm Rebating Cutter Bit - 491085. Reversible Carbide Tip

General Tools - Tungsten Carbide Tip Scribers $7.1 Versatile scribers. Tip is made from tungsten carbide. Ideal for use on metal, ceramic and glass surfaces. The tool's structure is interchangeable. Comes with a convenient pocket clip.

Carbide Scribe $9.95 Easily write on glass and metal with this durable tungsten carbide tip scribe. Scribe works just like a pen, enabling you to sign and date your stained glass projects and even mark valuables. Great for bandsaw owners to use for marking pattern lines that won and 39;t wash away when cutting.

Hillman Fastener Corp Hillman Fastener Corp 5 32x5-1 2 Carbide Tip 375222 $4.04 5/32x5-1/2 carbide tip Carbide tipped tapcon Shipped in quantities of 1 5/32 x 5-1/2? Brand #: Hillman Fastener Corp 375222 UPC: 075352643380 Keywords: tapcon drill bit carbide masonry scrwdr bits elco tipped

General Tools General Tools Carbide Scriber 88CM $5.61 Carbide scriber Tungsten carbide tip, Alnico permanent magnet Scriber point reverses Brand #: General Tools 88CM UPC: 038728311160 Keywords: carbide scriber & magnet

Blair 14003 Carbide Tip Antenna Hole Cut Kit $56.37 Carbide Holcutters are carbide tipped to offer improvedperformance and increased tool life in tough to cutmaterials such as stainless steel. These cutters easily cutthru the stock rather than ripping tearing and pushingthru as do typical hole saws. Dramatically outlasts bimetalhole saws and step drills.All cutters include arbor pilot and ejector spring. Thearbor fits 3/8 amp; 1/2 drill chucks. 3/4 1 amp; 11/4 Cutters Arbor amp; Extra Pilot

Spyderco C79Psbbk Assist with Carbide Tip Blk Blade Combo Edg $131.54 Emergency responders law enforcement officers and service professionals have made the Assist an indispensable part of their working gear. Its serrated blade offers tremendous cutting power and includes a PlainEdge section for detail work. The patented liftandpry blunt tip prevents accidental punctures and offers limited prying capability. A Cobra Hood ensures positive blade deployment even while wearing gloves and doubles as a thumb platform during use. Its retractable replaceable carbide glass breaker extends when the closed blade is squeezed into the handle and finger grooves in the handle allow scissor cutting of rope and cord with the partially open blade. This multifunction rescue tool even includes an emergency whistle in the handle.Specifications:Blade Length: 311/16 (94 mm)Cutting Edge: 33/16 (81 mm)Closed Length: 47/8 (124 mm)Overall Length: 83/8 (213 mm)Steel: VG10 Stainless SteelWeight: 4 oz. (115 g)Edge: Partially SerratedMade in JapanFeatures:Carbide glass breaker and whistleAmbidextrous tipup clipDavid Boye DentBiDirectional Textured 3D Black FRN HandlesCobra HoodHollowground blade

Dremel Dremel Carbide Engraver Point 9924 $5.07 Carbide engraver point Used for normal and engraving applications. creates fine lines and deep grooves For use with Dremel engraver model No. 290-01 Brand #: Dremel 9924 UPC: 080596099244 Keywords: engraver tip carbide point electric

KNK5KK9 Jobber Length Carbide Tip Drill Bit Set 5 Pieces $129.61 This drill bit can be used for drilling broken studs spring bolts die sections broken easy outs extra tough metals exotic metals brake drums and broken taps. Sizes include: 1/8 3/16 1/4 5/16 x 4 3/8 x 4 . Carbide tipped and made for use in drilling hardened steel in the range of 48 to 65 Rockwell C . Holes may be drilled without annealing or appreciably changing the structure of the material. Dimension: 4.2 W x 6.2 L x 1.25 H.

Tip On In $12.49 Tip On In

KnKut 5 Piece Jobber Length Carbide Tip Drill Bit Set. Each $89.79 Manufacturer: KnKut. Each. Features and Benefits: Carbide tipped and made for use in drilling hardened steel in the range of 48 to 65 Rockwell "C" Holes may be drilled without annealing or appreciably changing the structure of the material This drill bi

General Tools Tungsten Carbide Pointscriber. Each $4.65 Manufacturer: General Tools. Each. Tip Handle Length = 6 in No. of Points = 1 End Type = Straight Point Tip Material = Tungsten Carbide Handle Type = Round Handle Structure = Interchangeable Point Applicable Materials = Ceramics, Copper, Glass, Stainless

DeWalt 115DW5207 7 Piece Carbide Hammer Bit Set $38.22 Innovative tip configuration reduces walking for improved accuracy . Improved carbide tip provides up to 2X longer life . Optimum grade of carbide provides maximum durability . Unique flute design efficiently removes dust reducing bit binding

Singer Carbide Tip Movable Upper Knife Blade 412585, 60507, 61425 for14U 14SH 14CG Serger, Consew 14TU, Yamata FN14U, Simplicity Babylock Riccar Nancy $19.99 Singer Carbide Tip Movable Upper Knife Blade 412585, 60507, 61425 for14U 14SH 14CG Serger, Consew 14TU, Yamata FN14U, Simplicity Babylock Riccar Nancy

Irwin 58540010 C818R58 Carbide Bit $48.83 Hole in flute makes it easy to pull wire through walls ceilings and floors. Specially designed flute quickly clears masonry dust . Heavy duty 118 degree point enters material quickly . Carbide tip cutting edge ideal for use where masonry construction is encountered including brick mortar joints and cinder blocks

Irwin 58540005 C818R516 Carbide Bit $34.65 Hole in flute makes it easy to pull wire through walls ceilings and floors. Specially designed flute quickly clears masonry dust . Heavy duty 118 degree point enters material quickly . Carbide tip cutting edge ideal for use where masonry construction is encountered including brick mortar joints and cinder blocks

KnKut 5 PIece Carbide Tip Bit Set with 3 Pack of 1/8 Double End Bits. Each $82.67 Manufacturer: KnKut. Each. Features and Benefits: Carbide Tipped and made for use in drilling hardened steel in the range of 48 to 65 Rockwell "C" Holes may be drilled without annealing or appreciably changing the structure of the material Bonus 3 pack

General Tools - Tungsten Carbide Magnetic Scribers $8.6 Specialized scribers. Tip is made from tungsten carbide. Ideal for use on metal, ceramic and glass surfaces. A powerful magnet can be found on the tool's cap for cleaning up stray metal shavings. The tool's structure is interchangeable. Comes with a convenient pocket clip. Reversing scribe point for safe storage.

Irwin C818r-5/16" Carbide Bit. 1 Bit $23.07 Manufacturer: Irwin. 1 Bit. Hole in flute makes it easy to pull wire through walls, ceilings, and floors Specially designed flute quickly clears masonry dust Heavy duty 118 degree point enters material quickly Carbide tip cutting edge ideal for use where

Irwin C818r-3/8" Carbide Bit. 1 Bit $20.95 Manufacturer: Irwin. 1 Bit. Hole in flute makes it easy to pull wire through walls, ceilings, and floors Specially designed flute quickly clears masonry dust Heavy duty 118 degree point enters material quickly Carbide tip cutting edge ideal for use where

Irwin C818r-5/8" Carbide Bit. 1 Bit $35.92 Manufacturer: Irwin. 1 Bit. Hole in flute makes it easy to pull wire through walls, ceilings, and floors Specially designed flute quickly clears masonry dust Heavy duty 118 degree point enters material quickly Carbide tip cutting edge ideal for use where

General Tools 31888 Tungsten Carbide Pointscriber $20.83 Length: 6 . No. of Points: 1. End Type: Straight Point. Tip Material: Tungsten Carbide. Handle Type: Round. Structure: terchangeable Point. Applicable Materials: Ceramics Copper Glass Stainless Steel. Includes: Pocket Clip. Type: Free Line Scriber.

Brown & Sharpe Precision 44584 Carbide Scriber Code A. Each $27.72 Manufacturer: Brown & Sharpe Precision. Each. Works like a pen to retract point and save pockets End Tip Material = Carbide Handle Material = Satin Anodized Aluminum Type = Retractable Scriber Customers also search for: Discount 44584 Carbide Scriber Cod

85238M - 5/8 inch Hinge Mprtising Router Bit Carbide Tip $30.79 [114-85238M] Truck Delivery UPC: 000346049428

85216M - 1/2 inch Laminate Trim Bit 3-Flutes Carbide Tip $27.15 [114-85216M] Truck Delivery UPC: 000346049220

85251M - 1/2 inch Straight Bit Routerbit Carbide Tip $26.55 [114-85251M] Truck Delivery UPC: 000346277876

85249M - 1/2 inch Hinge Mortising Router Bit Carbide Tip $23.69 [114-85249M] Truck Delivery UPC: 000346049565

30212 - 12Ct 3/4 inch (19Mm) Carbide-Tip Hole Saw $28.08 [433-30212] Truck Delivery UPC: 082472302127

85265M - 3/4 inch Straight Router Bit2-Flutes Carbide Tip $24.97 [114-85265M] Truck Delivery UPC: 000346277890

Spyderco C79PSOR Assist Orange Frn Handle With Carbide Tip Comboedge $118.43 ATTRIBUTES. nbsp;Blade Material:nbsp;VG10. nbsp;Lock Style:nbsp;Lock Back

SPYDERCO C79PSBK Assist FRN Handle With Carbide Tip ComboEdge $118.43 Features a 3.36 in. VG10 steel blade. 4.88 in. black FRN handle with a survival whistle built in to the butt end. A reinforced wire pocket clip screws onto either side for both left righthanders.

Tungsten Carbide ID Bracelet $89.99 There are only a few tungsten ID Bracelet designs, this is one of the best. It has a gun metal color, high polish edges and satin finish center which makes look as two tone, the most beautiful fact about it is that the bracelet is non-scratchable, it will keep the same look for many years. If you do want to engrave any thing on ID link, you can still do it with Diamond tip (although it is pretty hard to make it). It measures in 8.5" long and about 13 mm wide. Brand: Tioneer Size/Dimensions: 8.5" Design: ID's & Initials Style: Chain & link Material: Tungsten Gender: Male Age: Adult Resizable: Yes

General Tools 31888CM Tungsten Carbide Pointscriber WMagnet $21.85 Marks hard materials including hardened steel ceramics and glass. Alnico permanent magnet for retrieving. Scribe point reverses for safety. Size: 6 Length. No. of Points: 1. End Type: Straight Point. Tip Material: Tungsten Carbide. Handle Type: Round. Structure: Interchangeable Point. Applicable Materials: Ceramics Copper Glass Stainless Steel. Includes: Pocket Clip. Free Line Scriber.

KNK5KK9318 Carbide Tip Bit Set with 3 Pack of .13in. Double End Bits 5 Pieces $119.32 Carbide Tipped and made for use in drilling hardened steel in the range of 48 to 65 Rockwell C . Holes may be drilled without annealing or appreciably changing the structure of the material. Bonus 3 pack of 1/8 Double End Drill Bits. KnKut 1/8 Double End Bits are surface treated for maximum lubricity. KnKut 1/8 Double End Bits feature a 135degree split point that will not walk. This drill bit can be used for drilling broken studs spring bolts die sections broken easy outs extra tough metals exotic metals brake drums etc. Heavy Pressure and low R.P.M. s recommended. Cutting oil should be used. Recommended for use in drill presses but can be used in portable drills. Set includes: 1 piece each: 1/8 3/16 1/4 5/16 x 4 3/8 x 4 . KnKut Double End Sheeter Drill Bits are excellent for thin gauge metals such as sheet metal. Made of himolybdenum tool steel and surface treated for maximum lubricity our sheeter drills feature a 135degree split point that will not walk. Dimension: 4.25 W x 5.5 L x 0.75 H.

Dewalt Tools 5 Piece Rock Carbide Sds Pl. 1 Set $26.99 Manufacturer: Dewalt Tools. 1 Set. Innovative tip design maximizes carbide surface contact for longer life Four flute design - Enlarged flutes clean debris out for fast efficient drilling Optimized core diameter maximizes hammer energy for greater impact

General Tools 6in. Tungsten Carbide Scriber Magnet 88CM $25.58 Tungsten carbide tip marks hard materials including hardened steel ceramics and glass. Alnico permanent magnet picks up small parts and retrieves steel chips from hard to reach places. Scriber point reverses for safety. 6 overall length. Carded. Length: 0.38. Width: 8.63. Height: 2.75

Black & Decker dwlt Black & Decker dwlt 6-1 2 in 24t Carbide Blade DW9154 $16.15 6-1/2? 24t carbide blade 6-1/2? thin kerf saw blades for use on cordless circular saws Carbide tip and anti-stick coating allow for quick cuts and reduced friction 24T Brand #: Black & Decker/DWLT DW9154 UPC: 028877311029 Keywords: circular saw blade for crdlss circ cordless

Black & Decker dwlt Black & Decker dwlt 6-1 2 in 16t Carbide Blade DW9155 $13.54 6-1/2? 16t carbide blade 6-1/2? thin kerf saw blades for use on cordless circular saws Carbide tip and anti-stick coating allow for quick cuts and reduced friction 18T Brand #: Black & Decker/DWLT DW9155 UPC: 028877311012 Keywords: circular saw blade for crdlss circ cordless