High Speed Drill

High Speed Drill

Drilling Holes Of Seashells - Making Of Seashell Jewelry

Seashell Jewelry Making

This article will describe some tips and advices how to drill holes of seashells in making of seashells jewelry. Drilling holes of seashells is quite difficult and shall be done very carefully. Seashells are often quite fragile. Be very careful drilling holes in them and also try to pick shells that are not chipping or flaking at the edges. There are a few precautions that we should know and take in order to prevent the seashells from crack and damage.

1 - Drilling bits

Use A Dremel. A Dremel tool works well also because it's higher speed than your regular drill. Especially good for delicate shells; use a very small bit. It wasn't possible to use a very fast speed because the hardness of the shell made the drill bit slip and mark the surface. Once the hole was started, continue with slow because even then the drill would overheat from the effort. We had to stop every 5 minutes and allow the drill to cool down for about 20 minutes to half an hour. Also suggested to use diamond points to drill.

2 - Water

When you drill with diamond points, always use water to cool the points or they will fail quickly. This also keeps the dust down, but wear a good quality filter mask or use a vacuume to catch any dust/spray. Seashell dust is toxic, and I don't mean a little bit toxic. You can really hurt yourself if you breath it in, or get it into your eyes, a cut or sore, or ingest it. Sometimes the particulates are so small you don't realize they're in the air around you. When you breathe this dust in, it gets embedded in your lungs and it won't come out. It will literally be there forever, and it's toxic. Obviously, don't put your drill in the water, just the tip of the bit doing the drilling.

3 - Start Drilling

Make sure the drill bit is sharp, and that you are using a high speed drill. Use the smallest drill bit that will accommodate the chain or whatever you're putting thru the shell. Secure the shell firmly in a vise or other arrangement to make sure it cannot move during the drilling.If the shell is thin, I would suggest putting tape over the spot where you are drilling to help prevent the shell from splintering or cracking.Lay the shell with the top up so that if spintering does occur as the bit reaches the other side, any splintering will be on the bottom (back) of the shell. If you're not comfortable using a drill, practice first on some scrap shells before drilling in those you want to use.

Now when you start to drill, you're going to do it like this: hold the drill in a straight up and down position so that the hole will be straight. Hold the drill firmly so that the bit won't go skidding across the surface of the stone. (Now you know why you need practice pieces.) You're going to touch the drill bit down semi-firmly, like you mean it, but then lift the drill bit out of the hole so water can pool inside it. Repeat. You can do it pretty quickly, too. Touch down, lift, touch down, lift, etc. When you're almost all the way though, Stop. Flip your stone over and begin to drill from the other side. This will prevent a "blow out" or chipping the stone or glass where the hole should be. It takes practice to do this, so don't be hard on yourself. Glass and stone will pretty much drill the same. Anything else may be unpredictable, so a practice piece is necessary.

For more information about Seashells Jewelry Making, visit Jewelry Skills. There are more useful tips and ideas in making of seashells jewelry.

Seashell Jewelry Making

About the Author

The Author from Telok Cempedak Beach Resort, Malaysia

Irwin® - High Speed Steel Drill Bit Sets $110.8 Heat and wear-resistant bit sets. Drill parts and accessories utilized best for wood, plastic and metal Bit is made of M-1 high speed steel Power tools with great combination of toughness, heat and wear resistance Graduation(s) are in 64ths Twist and drill bit sets with a cutting diameter of 1/16in minimum and 1/2in maximum HSS cutting edge and bright finishing Available with a metal index case and 29 per set

Milwaukee 1630-1 1/2-in Compact High Speed Reversible Drill, 900 RPM $219.99 1/2-in Compact High Speed Reversible Drill, 900 RPM - 1630-1. Pipe Handle. Product Manual

Bosch 1035VSR 1/2-in 8 Amp High-Speed Drill with Keyless Chuck $149.99 1/2" 8 Amp High-Speed Drill w/ Keyless Chuck - 1035VSR. Auxiliary Handle - 2 602 025 094

KNKKK5116 .06in. High Speed Steel and Titanium Coated Drill Bits $17.64 Premium grade KnKut Drill Bits are manufactured from a high grade M7 Molybdenum high speed steel that has a high vanadium content. KnKut Performance Drill Bits are salt nitride treated actually penetrating the tool s surface giving KnKut Drill Bits the

Williams Gunsight Co. 1767 High Speed Tap and Drill Set 648 $29.01 High speed tap and high speed drill set. Size: 648. Huge selection to choose from. Ready to ship at your convenience. High quality components. Satisfaction ensured.

Williams Gunsight Co. 1768 High Speed Tap and Drill Set 840 $29.01 High carbon steel tap with 3 flutes. Size: 840. High speed steel drill. Set in envelope. Huge selection to choose from. Satisfaction ensured.

Bosch 1013VSR 1/2-in 6.5 Amp High-Speed Drill $200 1/2" 6.5 Amp High-Speed Drill - 1013VSR. Auxiliary Handle - 2 602 025 094. Chuck Key - 2 610 348 635

Factory Reconditioned Bosch 1030VSR-46 3/8-in 7.5 Amp High-Speed Drill $99.99 3/8" 7.5 Amp High-Speed Drill - 1030VSR-46. Auxiliary Handle - 2 602 025 094. Chuck Key - 3 608 571 539

Bosch 1033VSR 1/2-in 8 Amp High-Speed Drill $219.99 1/2" 8 Amp High-Speed Drill - 1033VSR. Auxiliary Handle - 2 602 025 094. Chuck Key - 2 610 348 635

Factory Reconditioned Bosch 1013VSR-46 1/2-in 6.5 Amp High-Speed Drill $109.99 1/2" 6.5 Amp High-Speed Drill - 1013VSR-46. Auxiliary Handle - 2 602 025 094. Chuck Key - 2 610 348 635

Bosch 1030VSR 3/8-in 7.5 Amp High-Speed Drill $139.99 3/8" 7.5 Amp High-Speed Drill - 1030VSR. Auxiliary Handle - 2 602 025 094. Chuck Key - 3 608 571 539

Mountain MTNXDBS13WH 13 Piece High Speed Steel Drill Bit Set $28.34 The Mounitain (MTNXBDS13WH) 13 piece high speed steel drill bit set is ideal for many uses and is the perfect companion to most technicians tool boxes. Meets ANSI standards. 118 degree split point tip. 2 times stronger than other drill bit

Milwaukee Electric Tools 1/8" High Speed Pilot Drill. Each $4.91 Manufacturer: Milwaukee Electric Tools. Each. Features Benefits: For use with hole saw saw arbors MLW49-56-7010 and MLW49-56-7150 For general cutting of wood and metal One per package Customers also search for: Discount 1/8" High Speed Pilot Drill, Buy

Boschrotozipskil 20 Piece High Speed Steel Drill Bit Set 96020 $32.14 High speed steel drill bit set. 118deg; point for general purpose drilling applications. Sharp cutting edges deliver fast smooth cuts. Selection of the most common sizes. Includes storage case. 20 pieces. Carded. Length: 12.5. Width: 1.04. Height: 13.75

Factory Reconditioned Milwaukee 1630-8 1/2-in Compact High Speed Reversible Drill, 900 RPM $149.99 1/2-in Compact High Speed Reversible Drill, 900 RPM - 1630-8. Pipe Handle. Product Manual

Boschrotozipskil .50in. High Speed Drill 8.0A With Keyless Chuck 1035VSR $265.55 High speed drill with keyless chuck. 8.0 amp all ball bearing motor. Variable speed. Soft grip trigger. Lock on button for ease of operation. Precision cut steel gears. Extra long 8 rubber cord. 360 degree auxiliary handle with optional depth gauge.50 . Length: 13.5. Width: 3. Height: 9.75

Irwin Industrial Tool .20in. .2520NC High Speed Steel Drill Bit Tap 80230 $23.67 High speed drill bit and tap. General purpose. High carbon steel plug tap. 13/64 drill bit.25 20NC. Carded. Length: 5.75. Width: 0.13. Height: 1.5

Irwin Industrial Tool NO.16 1224NC High Speed Steel Drill Bit Tap 80222 $23.65 High speed drill bit and tap. General purpose. High carbon steel plug tap. #16 drill bit. 1224NC. Carded. Length: 5.75. Width: 0.5. Height: 1.25

Irwin Industrial Tool NO.G .3118NC High Speed Steel Drill Bit Tap 80235 $25.25 High speed drill bit and tap. General purpose. High carbon steel plug tap. #G drill bit. 5/16 18NC. Carded. Length: 8.5. Width: 0.5. Height: 2

Irwin Industrial Tool .11in. 632NC High Speed Steel Drill Bit Tap 80213 $22.99 High speed drill bit and tap. General purpose. High carbon steel plug tap. 7/64 drill bit. 632NC. Carded. Length: 5.75. Width: 0.5. Height: 1.5

Irwin Industrial Tool NO.29 832NC High Speed Steel Drill Bit Tap 80217 $23.19 High speed drill bit and tap. General purpose. High carbon steel plug tap. #29 drill bit. 832NC. Carded. Length: 5.75. Width: 0.13. Height: 1.5

Irwin Industrial Tool NO.25 1024NC High Speed Steel Drill Bit Tap 80220 $23.3 High speed drill bit and tap. General purpose. High carbon steel plug tap. #25 drill bit. 1024NC. Carded. Length: 5.75. Width: 0.5. Height: 1.5

Hanson HAN73117 .27in. Turbomax High Speed Steel Straight Shank Jobber Length Drill Bit $20.53 High performance metal drilling for portable drill users works well on curved surfaces. Revolutionary tip design stays sharper longer and drills up to 10 times faster than other leading drill bits. High speed steel features a black body and g

Hanson HAN73110 .16in. Turbomax High Speed Steel Straight Shank Jobber Length Drill Bit $18.01 High performance metal drilling for portable drill users works well on curved surfaces. Revolutionary tip design stays sharper longer and drills up to 10 times faster than other leading drill bits. High speed steel features a black body and g

Hanson HAN73124 .38in. Turbomax High Speed Steel Straight Shank Jobber Length Drill Bit $24.06 High performance metal drilling for portable drill users works well on curved surfaces. Revolutionary tip design stays sharper longer and drills up to 10 times faster than other leading drill bits. High speed steel features a black body and g

Hanson HAN73118 .28in. Turbomax High Speed Steel Straight Shank Jobber Length Drill Bit $21.02 High performance metal drilling for portable drill users works well on curved surfaces. Revolutionary tip design stays sharper longer and drills up to 10 times faster than other leading drill bits. High speed steel features a black body and g

Hanson HAN73123 .36in. Turbomax High Speed Steel Straight Shank Jobber Length Drill Bit $23.79 High performance metal drilling for portable drill users works well on curved surfaces. Revolutionary tip design stays sharper longer and drills up to 10 times faster than other leading drill bits. High speed steel features a black body and g

Hanson HAN73115 1.08in. Turbomax High Speed Steel Straight Shank Jobber Length Drill Bit $19.36 High performance metal drilling for portable drill users works well on curved surfaces. Revolutionary tip design stays sharper longer and drills up to 10 times faster than other leading drill bits. High speed steel features a black body and g