Masonry Drill Bit

Masonry Drill Bit

Drilling Holes The Right Way With Masonry Drill Bits

You might think that drilling a hole in a wall is easy to do and requires no training and minimal effort. Well, you are partially correct. Using a drill to place a hole in a wall is simple, but placing it correctly is a different matter entirely. Homes all across the nation have walls punctuated with holes that were drilled in completely the wrong way or else they are the incorrect size. That's correct, an unbelievable amount of DIY wannabes use a drill bit that is too large or small or else they drill straight through the wall when all they wanted to do was hang a picture. Most drilling jobs can be completed using masonry drill bits or a step drill bit. Although there are dozens of other options, these bits can do everything any other bit can do, only better.

Masonry drill bits have tips made from tungsten carbide which has been bonded to a steel shaft. Occasionally, a silicon bronze alloy will be used instead. These bits can drill through any surface that is concrete or stone based. While it is possible to use them in a hand brace, this is not advised as it takes far too much effort to produce a good result. When used in a power drill like it should be, these drill bits are remarkably effective. When drilling harder materials, be sure to have the drill operating at a low speed. Otherwise, the tip could overheat with cheaper bits having a propensity to shatter under the strain.

If you are drilling into metal, a step drill bit is the best option unless the metal is very thick. It gets its name because the drill bit increases in diameter from the tip to the shaft. They are designed to make the hole bigger as it drills through. With smaller drill bits of this kind, there is no need to use a pilot bit. When using a large step drill, ensure that a hole has already been drilled beforehand which is at least the diameter of the smallest step on the bit. Always wear some sort of safety equipment like goggles while drilling.

When drilling a metal hole, always use a center punch on the metal to mark off where you want the middle of the hole to be. This should ensure that the drill does not drift away from its intended target. Use the small step drill bit first and go straight through the hole as far as you can. Remove the small bit and replace it with the larger one. Place the tip of the drill bit into the hole just created and start drilling again. Continue until the hole is the exact diameter you planned it to be.

As you can see, whether you are using masonry drill bits to cut through brick or step drill bits to cut into metal, it is not as easy as pointing and aiming. It is important to protect your eyes at all times and also stop every few seconds to remove shavings from the drill bit as well as applying tapping fluid to ensure the bit works smoothly.

About the Author

For more information about
masonry drill bits
, please check out
step drill bit
.

DEWALT DW2571 3-Piece Rotary Masonry Drill Bit Set $15.99 3-Piece Rotary Masonry Drill Bit Set - DW2571. 5/32" Rotary Masonry Drill Bit. 3/16" Rotary Masonry Drill Bit. 1/4" Rotary Masonry Drill Bit

Mibro gs Mibro gs 7 16 in Masonry Drill Bit 260851DB $1.46 7/16? masonry drill bit For rotary drilling in concrete, brick, and masonry Fast spiral, double flutes quickly clear material from hole Zinc finish 7/16? x 6? (3/8? shank) Brand #: Mibro/GS 260851DB UPC: 009326315706 Keywords: masonry drill bit fast spiral

Mibro gs Mibro gs 1 2 in Masonry Drill Bit 260931DB $1.86 1/2? masonry drill bit For rotary drilling in concrete, brick, and masonry Fast spiral, double flutes quickly clear material from hole Zinc finish 1/2? x 6? (3/8? shank) Brand #: Mibro/GS 260931DB UPC: 009326315690 Keywords: masonry drill bit fast spiral

Mibro gs Mibro gs 5 8 in Masonry Drill Bit 261151DB $2.34 5/8? masonry drill bit For rotary drilling in concrete, brick, and masonry Fast spiral, double flutes quickly clear material from hole Zinc finish 5/8? x 6? (3/8? shank) Brand #: Mibro/GS 261151DB UPC: 009326315720 Keywords: masonry drill bit fast spiral

Mibro gs Mibro gs 3 4 in Masonry Drill Bit 261231DB $3.38 3/4? masonry drill bit For rotary drilling in concrete, brick, and masonry Fast spiral, double flutes quickly clear material from hole Zinc finish 3/4? x 6? (3/8? shank) Brand #: Mibro/GS 261231DB UPC: 009326315737 Keywords: masonry drill bit fast spiral

Mibro gs Mibro gs 5 32 in Masonry Drill Bit 374191DB $1.16 5/32? masonry drill bit For rotary drilling in concrete, brick, and masonry Fast spiral, double flutes quickly clear material from hole Zinc finish 5/32? x 4-1/2? Brand #: Mibro/GS 374191DB UPC: 009326315867 Keywords: masonry drill bit fast spiral

Mibro gs Mibro gs 3 8 in Masonry Drill Bit 223811DB $1.48 3/8? masonry drill bit For rotary drilling in concrete, brick, and masonry Fast spiral, double flutes quickly clear material from hole Zinc finish 3/8? x 6? Brand #: Mibro/GS 223811DB UPC: 009326315683 Keywords: masonry drill bit fast spiral

Mibro gs Mibro gs 5 16 in Masonry Drill Bit 260691DB $1.23 5/16? masonry drill bit For rotary drilling in concrete, brick, and masonry Fast spiral, double flutes quickly clear material from hole Zinc finish 5/16? x 4-3/4? Brand #: Mibro/GS 260691DB UPC: 009326315676 Keywords: masonry drill bit fast spiral

Lindemann 601714 Malco .25 Inch Masonry Bit $26.62 Masonry Drill Bit is used for drilling holes for masonry anchors or screws. Size: 1/4 . High quality components. Satisfaction ensured.

Irwin Industrial Tool .75in. X 13in. Masonry Drill Bit 5026022 $20.77 Masonry bit. For drilling concrete masonry brick tile and plaster. Use only in rotary drills. Tungsten carbide tip. 13 long.75 diameter bit. Carded

Black & Decker Black & Decker 1 2x12 Masonry Drill Bit 16745 $9.12 1/2x12 masonry drill bit Carbide-tips For light-duty use in rotary drills in soft or medium-hard masonry Speed-tip drills up to 2 times faster Innovative design reduces breakage and improves dust removal 1/2 x 12 Brand #: Black & Decker 16745 UPC: 028874167452 Keywords: drill bit masonry carbide tip

Black & Decker Black & Decker 1 4x12 Masonry Drill Bit 16742 $5.15 1/4x12 masonry drill bit Carbide-tips For light-duty use in rotary drills in soft or medium-hard masonry Speed-tip drills up to 2 times faster Innovative design reduces breakage and improves dust removal 1/4 x 12 Brand #: Black & Decker 16742 UPC: 028874167421 Keywords: drill bit masonry carbide tip

Black & Decker Black & Decker 3 8x12 Masonry Drill Bit 16744 $6.43 3/8x12 masonry drill bit Carbide-tips For light-duty use in rotary drills in soft or medium-hard masonry Speed-tip drills up to 2 times faster Innovative design reduces breakage and improves dust removal 3/8 x 12 Brand #: Black & Decker 16744 UPC: 028874167445 Keywords: drill bit masonry carbide tip

Black & Decker Black & Decker 5 8x12 Masonry Drill Bit 16746 $8.97 5/8x12 masonry drill bit Carbide-tips For light-duty use in rotary drills in soft or medium-hard masonry Speed-tip drills up to 2 times faster Innovative design reduces breakage and improves dust removal 5/8 x 12 Brand #: Black & Decker 16746 UPC: 028874167469 Keywords: drill bit masonry carbide tip

Black & Decker Black & Decker 3 4x12 Masonry Drill Bit 16747 $10.52 3/4x12 masonry drill bit Carbide-tips For light-duty use in rotary drills in soft or medium-hard masonry Speed-tip drills up to 2 times faster Innovative design reduces breakage and improves dust removal 3/4 x 12 Brand #: Black & Decker 16747 UPC: 028874167476 Keywords: drill bit masonry carbide tip

Irwin Industrial Tool .50in. X 13in. Masonry Drill Bit 5026016 $28.46 Masonry bit. For drilling concrete masonry brick tile slate and plaster. Use only in rotary drills. Tungsten carbide tips.38 diameter shank. 13 length.50 diameter bit

Irwin Industrial Tool .31in. X 13in. Masonry Drill Bit 5026008 $26.42 Masonry bit. For drilling concrete masonry brick tile slate and plaster. Use only in rotary drills. Tungsten carbide tips.25 diameter shank. 13 long. 5/16 diameter bit. Carded

Black & Decker dwlt Black & Decker dwlt 5 32 in Masonry Drill Bit DW2572 $3.87 5/32? masonry drill bit Hex shank masonry bit for Rapid Load system Carbide tipped bit for aggresive penetration For drilling brick, block, and concrete 5/32? Brand #: Black & Decker/DWLT DW2572 UPC: 028874025721 Keywords: drill bit masonry hex shank

Lindemann 601707 Malco 3 16 Inches Masonry Bit $25.69 Masonry Drill Bit is used for drilling holes for masonry anchors or screws. Size: 3/16 . High quality components. Satisfaction ensured.

Irwin Irwin 5 16x13 Masonry Bit 5026008 $5.3 5/16x13 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 5/16? diameter bit, 1/4? diameter shank, 13? long Brand #: Irwin 5026008 UPC: 024721029157 Keywords: bit masonry drill carbide tip

Irwin Irwin 3 8x4 Masonry Bit 5026009 $2.98 3/8x4 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 3/8? diameter bit, 3/8? diameter shank, 4? long Brand #: Irwin 5026009 UPC: 024721029034 Keywords: bit masonry drill carbide tip

Irwin Irwin 3 8x13 Masonry Bit 5026011 $6.3 3/8x13 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 3/8? diameter bit, 3/8? diameter shank, 13? long Brand #: Irwin 5026011 UPC: 024721029164 Keywords: bit masonry drill carbide tip

Irwin Irwin 7 16x6 Masonry Bit 5026012 $3.98 7/16x6 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 7/16? diameter bit, 3/8? diameter shank, 6? long Brand #: Irwin 5026012 UPC: 024721028990 Keywords: bit masonry drill carbide tip

Irwin Irwin 1 2x6 in Masonry Bit 5026015 $5.53 1/2x6? masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 1/2? diameter bit, 3/8? diameter shank, 6? long Brand #: Irwin 5026015 UPC: 024721029089 Keywords: bit masonry drill carbide tip

Irwin Irwin 1 2x13 Masonry Bit 5026016 $8.28 1/2x13 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 1/2? diameter bit, 3/8? diameter shank, 13? long Brand #: Irwin 5026016 UPC: 024721029188 Keywords: bit masonry drill carbide tip

Irwin Irwin 5 8x6 Masonry Bit 5026019 $6.73 5/8x6 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 5/8? diameter bit, 3/8? diameter shank, 6? long Brand #: Irwin 5026019 UPC: 024721029003 Keywords: bit masonry drill carbide tip

Irwin Irwin 5 8x13 Masonry Bit 5026020 $9.92 5/8x13 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 5/8? diameter bit, 3/8? diameter shank, 13? long Brand #: Irwin 5026020 UPC: 024721029195 Keywords: bit masonry drill carbide tip

Irwin Irwin 3 4x6 Masonry Bit 5026021 $10.05 3/4x6 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 3/4? diameter bit, 3/8? diameter shank, 6? long Brand #: Irwin 5026021 UPC: 024721029041 Keywords: bit masonry drill carbide tip

Irwin Irwin 3 4x13 Masonry Bit 5026022 $15.9 3/4x13 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 3/4? diameter bit, 3/8? diameter shank, 13? long Brand #: Irwin 5026022 UPC: 024721029201 Keywords: bit masonry drill carbide tip

Irwin Irwin 1x6 Masonry Bit 5026023 $14.3 1x6 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 1? diameter bit, 1/2? diameter shank, 6? long Brand #: Irwin 5026023 UPC: 024721029133 Keywords: bit masonry drill carbide tip

Irwin Irwin 1 8x3 Masonry Bit 5026000 $1.33 1/8x3 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 1/8? diameter bit, 1/8? diameter shank, 3? long Brand #: Irwin 5026000 UPC: 024721029065 Keywords: bit masonry drill carbide tip

Irwin Irwin 5 32x3 Masonry Bit 5026001 $1.37 5/32x3 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 5/32? diameter bit, 5/32? diameter shank, 3? long Brand #: Irwin 5026001 UPC: 024721029010 Keywords: bit masonry drill carbide tip

Irwin Irwin 3 16x4 Masonry Bit 5026002 $1.46 3/16x4 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 3/16? diameter bit, 3/16? diameter shank, 4? long Brand #: Irwin 5026002 UPC: 024721029058 Keywords: bit masonry drill carbide tip

Irwin Irwin 1 4x4 Masonry Bit 5026003 $1.61 1/4x4 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 1/4? diameter bit, 1/4? diameter shank, 4? long Brand #: Irwin 5026003 UPC: 024721029072 Keywords: bit masonry drill carbide tip

Irwin Irwin 1 4x13 Masonry Bit 5026005 $4.59 1/4x13 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 1/4? diameter bit, 1/4? diameter shank, 13? long Brand #: Irwin 5026005 UPC: 024721029140 Keywords: bit masonry drill carbide tip

Irwin Irwin 5 16x4 Masonry Bit 5026006 $2.11 5/16x4 masonry bit Tungsten carbide tips For drilling concrete, masonry, brick, tile, slate, and plaster Use only in rotary drills 5/16? diameter bit, 1/4? diameter shank, 4? long Brand #: Irwin 5026006 UPC: 024721029027 Keywords: bit masonry drill carbide tip

Dw2573 - 3/16In Masonry Drill Bit $6.01 [6088264] UPC: 028874025738 1.25L x 0.4W x 6.75H 0.75 LB 0 Cubes

Dw2572 - 5/32In Masonry Drill Bit $5.9 [6088256] UPC: 028874025721 1.25L x 0.4W x 6.75H 0.75 LB 0 Cubes